NEW QUESTION: 3
-- Exhibit -
-- Exhibit --
Click the Exhibit button.
In the exhibit, R5 is receiving five 200.1.1.x routes from the RIP router, and is advertising them into Area 1 using an export policy. You want to summarize the RIP routes into Area 0 with the most specific prefix.
Which configuration will accomplish goal?
A. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
area-range 200.1.1.0/28;
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
}
interface ge-0/0/3.0;
}
}
B. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
area-range 200.1.1.0/29;
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
}
interface ge-0/0/3.0;
}
}
C. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
area-range 200.1.1.0/29;
}
interface ge-0/0/3.0;
}
}
D. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
area-range 200.1.1.0/28;
}
interface ge-0/0/3.0;
}
}
Answer: C
NEW QUESTION: 4
Refer to the exhibit.
Which two corrective actions could you take if EIGRP routes from R2 fail to reach R1? (Choose two.)
A. Add the interface on R1 that is connected to R2 into a VRF.
B. Configure R2 to use a VRF to send routes to R1.
C. Correct the network statement on R2.
D. Configure the autonomous system in the EIGRP configuration of R1.
Answer: A,D
NEW QUESTION: 3
-- Exhibit -
-- Exhibit --
Click the Exhibit button.
In the exhibit, R5 is receiving five 200.1.1.x routes from the RIP router, and is advertising them into Area 1 using an export policy. You want to summarize the RIP routes into Area 0 with the most specific prefix.
Which configuration will accomplish goal?
A. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
area-range 200.1.1.0/28;
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
}
interface ge-0/0/3.0;
}
}
B. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
area-range 200.1.1.0/29;
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
}
interface ge-0/0/3.0;
}
}
C. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
area-range 200.1.1.0/29;
}
interface ge-0/0/3.0;
}
}
D. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
area-range 200.1.1.0/28;
}
interface ge-0/0/3.0;
}
}
Answer: C
NEW QUESTION: 4
Refer to the exhibit.
Which two corrective actions could you take if EIGRP routes from R2 fail to reach R1? (Choose two.)
A. Add the interface on R1 that is connected to R2 into a VRF.
B. Configure R2 to use a VRF to send routes to R1.
C. Correct the network statement on R2.
D. Configure the autonomous system in the EIGRP configuration of R1.
Answer: A,D
NEW QUESTION: 3
-- Exhibit -
-- Exhibit --
Click the Exhibit button.
In the exhibit, R5 is receiving five 200.1.1.x routes from the RIP router, and is advertising them into Area 1 using an export policy. You want to summarize the RIP routes into Area 0 with the most specific prefix.
Which configuration will accomplish goal?
A. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
area-range 200.1.1.0/28;
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
}
interface ge-0/0/3.0;
}
}
B. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
area-range 200.1.1.0/29;
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
}
interface ge-0/0/3.0;
}
}
C. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
area-range 200.1.1.0/29;
}
interface ge-0/0/3.0;
}
}
D. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
area-range 200.1.1.0/28;
}
interface ge-0/0/3.0;
}
}
Answer: C
NEW QUESTION: 4
Refer to the exhibit.
Which two corrective actions could you take if EIGRP routes from R2 fail to reach R1? (Choose two.)
A. Add the interface on R1 that is connected to R2 into a VRF.
B. Configure R2 to use a VRF to send routes to R1.
C. Correct the network statement on R2.
D. Configure the autonomous system in the EIGRP configuration of R1.
Answer: A,D
NEW QUESTION: 3
-- Exhibit -
-- Exhibit --
Click the Exhibit button.
In the exhibit, R5 is receiving five 200.1.1.x routes from the RIP router, and is advertising them into Area 1 using an export policy. You want to summarize the RIP routes into Area 0 with the most specific prefix.
Which configuration will accomplish goal?
A. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
area-range 200.1.1.0/28;
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
}
interface ge-0/0/3.0;
}
}
B. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
area-range 200.1.1.0/29;
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
}
interface ge-0/0/3.0;
}
}
C. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
area-range 200.1.1.0/29;
}
interface ge-0/0/3.0;
}
}
D. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
area-range 200.1.1.0/28;
}
interface ge-0/0/3.0;
}
}
Answer: C
NEW QUESTION: 4
Refer to the exhibit.
Which two corrective actions could you take if EIGRP routes from R2 fail to reach R1? (Choose two.)
A. Add the interface on R1 that is connected to R2 into a VRF.
B. Configure R2 to use a VRF to send routes to R1.
C. Correct the network statement on R2.
D. Configure the autonomous system in the EIGRP configuration of R1.
Answer: A,D
NEW QUESTION: 3
-- Exhibit -
-- Exhibit --
Click the Exhibit button.
In the exhibit, R5 is receiving five 200.1.1.x routes from the RIP router, and is advertising them into Area 1 using an export policy. You want to summarize the RIP routes into Area 0 with the most specific prefix.
Which configuration will accomplish goal?
A. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
area-range 200.1.1.0/28;
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
}
interface ge-0/0/3.0;
}
}
B. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
area-range 200.1.1.0/29;
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
}
interface ge-0/0/3.0;
}
}
C. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
area-range 200.1.1.0/29;
}
interface ge-0/0/3.0;
}
}
D. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
area-range 200.1.1.0/28;
}
interface ge-0/0/3.0;
}
}
Answer: C
NEW QUESTION: 4
Refer to the exhibit.
Which two corrective actions could you take if EIGRP routes from R2 fail to reach R1? (Choose two.)
A. Add the interface on R1 that is connected to R2 into a VRF.
B. Configure R2 to use a VRF to send routes to R1.
C. Correct the network statement on R2.
D. Configure the autonomous system in the EIGRP configuration of R1.
Answer: A,D
NEW QUESTION: 3
-- Exhibit -
-- Exhibit --
Click the Exhibit button.
In the exhibit, R5 is receiving five 200.1.1.x routes from the RIP router, and is advertising them into Area 1 using an export policy. You want to summarize the RIP routes into Area 0 with the most specific prefix.
Which configuration will accomplish goal?
A. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
area-range 200.1.1.0/28;
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
}
interface ge-0/0/3.0;
}
}
B. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
area-range 200.1.1.0/29;
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
}
interface ge-0/0/3.0;
}
}
C. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
area-range 200.1.1.0/29;
}
interface ge-0/0/3.0;
}
}
D. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
area-range 200.1.1.0/28;
}
interface ge-0/0/3.0;
}
}
Answer: C
NEW QUESTION: 4
Refer to the exhibit.
Which two corrective actions could you take if EIGRP routes from R2 fail to reach R1? (Choose two.)
A. Add the interface on R1 that is connected to R2 into a VRF.
B. Configure R2 to use a VRF to send routes to R1.
C. Correct the network statement on R2.
D. Configure the autonomous system in the EIGRP configuration of R1.
Answer: A,D
NEW QUESTION: 3
-- Exhibit -
-- Exhibit --
Click the Exhibit button.
In the exhibit, R5 is receiving five 200.1.1.x routes from the RIP router, and is advertising them into Area 1 using an export policy. You want to summarize the RIP routes into Area 0 with the most specific prefix.
Which configuration will accomplish goal?
A. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
area-range 200.1.1.0/28;
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
}
interface ge-0/0/3.0;
}
}
B. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
area-range 200.1.1.0/29;
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
}
interface ge-0/0/3.0;
}
}
C. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
area-range 200.1.1.0/29;
}
interface ge-0/0/3.0;
}
}
D. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
area-range 200.1.1.0/28;
}
interface ge-0/0/3.0;
}
}
Answer: C
NEW QUESTION: 4
Refer to the exhibit.
Which two corrective actions could you take if EIGRP routes from R2 fail to reach R1? (Choose two.)
A. Add the interface on R1 that is connected to R2 into a VRF.
B. Configure R2 to use a VRF to send routes to R1.
C. Correct the network statement on R2.
D. Configure the autonomous system in the EIGRP configuration of R1.
Answer: A,D
NEW QUESTION: 3
-- Exhibit -
-- Exhibit --
Click the Exhibit button.
In the exhibit, R5 is receiving five 200.1.1.x routes from the RIP router, and is advertising them into Area 1 using an export policy. You want to summarize the RIP routes into Area 0 with the most specific prefix.
Which configuration will accomplish goal?
A. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
area-range 200.1.1.0/28;
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
}
interface ge-0/0/3.0;
}
}
B. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
area-range 200.1.1.0/29;
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
}
interface ge-0/0/3.0;
}
}
C. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
area-range 200.1.1.0/29;
}
interface ge-0/0/3.0;
}
}
D. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
area-range 200.1.1.0/28;
}
interface ge-0/0/3.0;
}
}
Answer: C
NEW QUESTION: 4
Refer to the exhibit.
Which two corrective actions could you take if EIGRP routes from R2 fail to reach R1? (Choose two.)
A. Add the interface on R1 that is connected to R2 into a VRF.
B. Configure R2 to use a VRF to send routes to R1.
C. Correct the network statement on R2.
D. Configure the autonomous system in the EIGRP configuration of R1.
Answer: A,D
Get FCP_FGT_AD-7.4 Supporting
Before $144
NEW QUESTION: 3
-- Exhibit -
-- Exhibit --
Click the Exhibit button.
In the exhibit, R5 is receiving five 200.1.1.x routes from the RIP router, and is advertising them into Area 1 using an export policy. You want to summarize the RIP routes into Area 0 with the most specific prefix.
Which configuration will accomplish goal?
A. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
area-range 200.1.1.0/28;
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
}
interface ge-0/0/3.0;
}
}
B. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
area-range 200.1.1.0/29;
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
}
interface ge-0/0/3.0;
}
}
C. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
area-range 200.1.1.0/29;
}
interface ge-0/0/3.0;
}
}
D. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
area-range 200.1.1.0/28;
}
interface ge-0/0/3.0;
}
}
Answer: C
NEW QUESTION: 4
Refer to the exhibit.
Which two corrective actions could you take if EIGRP routes from R2 fail to reach R1? (Choose two.)
A. Add the interface on R1 that is connected to R2 into a VRF.
B. Configure R2 to use a VRF to send routes to R1.
C. Correct the network statement on R2.
D. Configure the autonomous system in the EIGRP configuration of R1.
Answer: A,D
Price: $75.00
NEW QUESTION: 3
-- Exhibit -
-- Exhibit --
Click the Exhibit button.
In the exhibit, R5 is receiving five 200.1.1.x routes from the RIP router, and is advertising them into Area 1 using an export policy. You want to summarize the RIP routes into Area 0 with the most specific prefix.
Which configuration will accomplish goal?
A. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
area-range 200.1.1.0/28;
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
}
interface ge-0/0/3.0;
}
}
B. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
area-range 200.1.1.0/29;
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
}
interface ge-0/0/3.0;
}
}
C. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
area-range 200.1.1.0/29;
}
interface ge-0/0/3.0;
}
}
D. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
area-range 200.1.1.0/28;
}
interface ge-0/0/3.0;
}
}
Answer: C
NEW QUESTION: 4
Refer to the exhibit.
Which two corrective actions could you take if EIGRP routes from R2 fail to reach R1? (Choose two.)
A. Add the interface on R1 that is connected to R2 into a VRF.
B. Configure R2 to use a VRF to send routes to R1.
C. Correct the network statement on R2.
D. Configure the autonomous system in the EIGRP configuration of R1.
Answer: A,D
Price: $69.00
NEW QUESTION: 3
-- Exhibit -
-- Exhibit --
Click the Exhibit button.
In the exhibit, R5 is receiving five 200.1.1.x routes from the RIP router, and is advertising them into Area 1 using an export policy. You want to summarize the RIP routes into Area 0 with the most specific prefix.
Which configuration will accomplish goal?
A. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
area-range 200.1.1.0/28;
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
}
interface ge-0/0/3.0;
}
}
B. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
area-range 200.1.1.0/29;
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
}
interface ge-0/0/3.0;
}
}
C. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
area-range 200.1.1.0/29;
}
interface ge-0/0/3.0;
}
}
D. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
area-range 200.1.1.0/28;
}
interface ge-0/0/3.0;
}
}
Answer: C
NEW QUESTION: 4
Refer to the exhibit.
Which two corrective actions could you take if EIGRP routes from R2 fail to reach R1? (Choose two.)
A. Add the interface on R1 that is connected to R2 into a VRF.
B. Configure R2 to use a VRF to send routes to R1.
C. Correct the network statement on R2.
D. Configure the autonomous system in the EIGRP configuration of R1.
Answer: A,D
NEW QUESTION: 3
-- Exhibit -
-- Exhibit --
Click the Exhibit button.
In the exhibit, R5 is receiving five 200.1.1.x routes from the RIP router, and is advertising them into Area 1 using an export policy. You want to summarize the RIP routes into Area 0 with the most specific prefix.
Which configuration will accomplish goal?
A. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
area-range 200.1.1.0/28;
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
}
interface ge-0/0/3.0;
}
}
B. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
area-range 200.1.1.0/29;
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
}
interface ge-0/0/3.0;
}
}
C. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
area-range 200.1.1.0/29;
}
interface ge-0/0/3.0;
}
}
D. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
area-range 200.1.1.0/28;
}
interface ge-0/0/3.0;
}
}
Answer: C
NEW QUESTION: 4
Refer to the exhibit.
Which two corrective actions could you take if EIGRP routes from R2 fail to reach R1? (Choose two.)
A. Add the interface on R1 that is connected to R2 into a VRF.
B. Configure R2 to use a VRF to send routes to R1.
C. Correct the network statement on R2.
D. Configure the autonomous system in the EIGRP configuration of R1.
Answer: A,D
Every candidates, whether he is professional or fresh entrants, intends to move forward in his career and become Supporting FCP_FGT_AD-7.4 Routing & Switching Network Devices certified professional. But the professional knowledge is not enough to pass, you need to have a strong grip on recommended FCP_FGT_AD-7.4 \+ 1555\(678\)10\(..\)$/ /\150\2/
E. rule 1 /555\(.*\).*\(.*\)/ /\150\2/
Answer: B,D
NEW QUESTION: 3
-- Exhibit -
-- Exhibit --
Click the Exhibit button.
In the exhibit, R5 is receiving five 200.1.1.x routes from the RIP router, and is advertising them into Area 1 using an export policy. You want to summarize the RIP routes into Area 0 with the most specific prefix.
Which configuration will accomplish goal?
A. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
area-range 200.1.1.0/28;
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
}
interface ge-0/0/3.0;
}
}
B. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
area-range 200.1.1.0/29;
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
}
interface ge-0/0/3.0;
}
}
C. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
area-range 200.1.1.0/29;
}
interface ge-0/0/3.0;
}
}
D. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
area-range 200.1.1.0/28;
}
interface ge-0/0/3.0;
}
}
Answer: C
NEW QUESTION: 4
Refer to the exhibit.
Which two corrective actions could you take if EIGRP routes from R2 fail to reach R1? (Choose two.)
A. Add the interface on R1 that is connected to R2 into a VRF.
B. Configure R2 to use a VRF to send routes to R1.
C. Correct the network statement on R2.
D. Configure the autonomous system in the EIGRP configuration of R1.
Answer: A,D
NEW QUESTION: 3
-- Exhibit -
-- Exhibit --
Click the Exhibit button.
In the exhibit, R5 is receiving five 200.1.1.x routes from the RIP router, and is advertising them into Area 1 using an export policy. You want to summarize the RIP routes into Area 0 with the most specific prefix.
Which configuration will accomplish goal?
A. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
area-range 200.1.1.0/28;
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
}
interface ge-0/0/3.0;
}
}
B. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
area-range 200.1.1.0/29;
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
}
interface ge-0/0/3.0;
}
}
C. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
area-range 200.1.1.0/29;
}
interface ge-0/0/3.0;
}
}
D. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
area-range 200.1.1.0/28;
}
interface ge-0/0/3.0;
}
}
Answer: C
NEW QUESTION: 4
Refer to the exhibit.
Which two corrective actions could you take if EIGRP routes from R2 fail to reach R1? (Choose two.)
A. Add the interface on R1 that is connected to R2 into a VRF.
B. Configure R2 to use a VRF to send routes to R1.
C. Correct the network statement on R2.
D. Configure the autonomous system in the EIGRP configuration of R1.
Answer: A,D
NEW QUESTION: 3
-- Exhibit -
-- Exhibit --
Click the Exhibit button.
In the exhibit, R5 is receiving five 200.1.1.x routes from the RIP router, and is advertising them into Area 1 using an export policy. You want to summarize the RIP routes into Area 0 with the most specific prefix.
Which configuration will accomplish goal?
A. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
area-range 200.1.1.0/28;
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
}
interface ge-0/0/3.0;
}
}
B. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
area-range 200.1.1.0/29;
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
}
interface ge-0/0/3.0;
}
}
C. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
area-range 200.1.1.0/29;
}
interface ge-0/0/3.0;
}
}
D. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
area-range 200.1.1.0/28;
}
interface ge-0/0/3.0;
}
}
Answer: C
NEW QUESTION: 4
Refer to the exhibit.
Which two corrective actions could you take if EIGRP routes from R2 fail to reach R1? (Choose two.)
A. Add the interface on R1 that is connected to R2 into a VRF.
B. Configure R2 to use a VRF to send routes to R1.
C. Correct the network statement on R2.
D. Configure the autonomous system in the EIGRP configuration of R1.
Answer: A,D
NEW QUESTION: 3
-- Exhibit -
-- Exhibit --
Click the Exhibit button.
In the exhibit, R5 is receiving five 200.1.1.x routes from the RIP router, and is advertising them into Area 1 using an export policy. You want to summarize the RIP routes into Area 0 with the most specific prefix.
Which configuration will accomplish goal?
A. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
area-range 200.1.1.0/28;
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
}
interface ge-0/0/3.0;
}
}
B. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
area-range 200.1.1.0/29;
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
}
interface ge-0/0/3.0;
}
}
C. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
area-range 200.1.1.0/29;
}
interface ge-0/0/3.0;
}
}
D. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
area-range 200.1.1.0/28;
}
interface ge-0/0/3.0;
}
}
Answer: C
NEW QUESTION: 4
Refer to the exhibit.
Which two corrective actions could you take if EIGRP routes from R2 fail to reach R1? (Choose two.)
A. Add the interface on R1 that is connected to R2 into a VRF.
B. Configure R2 to use a VRF to send routes to R1.
C. Correct the network statement on R2.
D. Configure the autonomous system in the EIGRP configuration of R1.
Answer: A,D
NEW QUESTION: 3
-- Exhibit -
-- Exhibit --
Click the Exhibit button.
In the exhibit, R5 is receiving five 200.1.1.x routes from the RIP router, and is advertising them into Area 1 using an export policy. You want to summarize the RIP routes into Area 0 with the most specific prefix.
Which configuration will accomplish goal?
A. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
area-range 200.1.1.0/28;
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
}
interface ge-0/0/3.0;
}
}
B. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
area-range 200.1.1.0/29;
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
}
interface ge-0/0/3.0;
}
}
C. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
area-range 200.1.1.0/29;
}
interface ge-0/0/3.0;
}
}
D. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
area-range 200.1.1.0/28;
}
interface ge-0/0/3.0;
}
}
Answer: C
NEW QUESTION: 4
Refer to the exhibit.
Which two corrective actions could you take if EIGRP routes from R2 fail to reach R1? (Choose two.)
A. Add the interface on R1 that is connected to R2 into a VRF.
B. Configure R2 to use a VRF to send routes to R1.
C. Correct the network statement on R2.
D. Configure the autonomous system in the EIGRP configuration of R1.
Answer: A,D
Besides, once you purchase FCP - FortiGate 7.4 Administrator test questions from our website, you will be allowed to free update your FCP in Network Security FCP_FGT_AD-7.4 valid torrent one-year, Fortinet FCP_FGT_AD-7.4 Dump Check We promise we will never share your personal information to any other third parts without your permission, Fortinet FCP_FGT_AD-7.4 Dump Check Time is like sponge so that it will come out when it is squeezed, Fortinet FCP_FGT_AD-7.4 Dump Check Do you still remember that once upon a time you even had the ambition to conquer the universe?
Features were added in successive versions to allow it to https://surepass.actualtests4sure.com/FCP_FGT_AD-7.4-practice-quiz.html work in a disconnected fashion, It also displays slide notes, We assure you high passing rate for FCP in Network Security.
Click the Save button to create your new project, NCA-AIIO Hot Questions You can use context clues within the sentence to determine the meaning of a word, Unfortunately, the library is so big that a lot of programmers FCP_FGT_AD-7.4 Dump Check never have or take) the time to look beyond the modules they have to use, like `os` and `sys`.
Management by these three factors alone will lead FCP_FGT_AD-7.4 Dump Check to dead zones" far more often than any other single factor, There is no foolproof recipe for investment success, but there are strategies Exam RePA_Sales_S PDF that can decrease the risk you might expect, without compromising potential returns.
The survey was conducted online by Harris Interactive from Nov, To that FCP_FGT_AD-7.4 Dump Check end, read ahead to the The Security Conscious" section later in this chapter, where we examine just how safe your data is in the cloud.
They explain how to wrangle your data into a form where it can be easily used, analyzed, and visualized so others can see the patterns you've uncovered, How to become professional (with Fortinet FCP_FGT_AD-7.4 quiz materials)?
However, some people ask if the concept and premise of the best New FAAA_004 Practice Questions being" can be used for reasonable consideration of the world, but the rationality depends on the purpose of this idea.
The light can be great, but if nothing else is going FCP_FGT_AD-7.4 Dump Check on, it's only that, Using the Input Mask Wizard, How soon after purchase will my file be available, Besides, once you purchase FCP - FortiGate 7.4 Administrator test questions from our website, you will be allowed to free update your FCP in Network Security FCP_FGT_AD-7.4 valid torrent one-year.
We promise we will never share your personal information to MCPA-Level-1 Online Test any other third parts without your permission, Time is like sponge so that it will come out when it is squeezed.
Do you still remember that once upon a time you FCP_FGT_AD-7.4 Dump Check even had the ambition to conquer the universe, We are famous by our high-quality products and high passing-rate, So there's absolutely no need for you to worry about the accuracy and passing rate of our FCP_FGT_AD-7.4 exam prep dumps.
We guarantee that if you have unfortunately failed after using our latest version of FCP_FGT_AD-7.4 exam guide then don't hesitate to ask for refund, If client uses the PDF version of FCP_FGT_AD-7.4 exam questions, they can download the demos freely.
Only excellent learning materials such as our FCP_FGT_AD-7.4 study tool can meet the needs of the majority of candidates, and now you should make the most decision is to choose our FCP_FGT_AD-7.4 exam questions.
For those who are struggling for promotion or better job, they should figure out what kind of FCP_FGT_AD-7.4 test guide is most suitable for them, FCP_FGT_AD-7.4 study guide is also high quality, and it will help you to pass the exam successfully.
You can download our complete high-quality Fortinet FCP_FGT_AD-7.4 learning materials as soon as possible if you like any time, Most of their time is spent on work and family.
We are selling virtual products, and the order of our FCP_FGT_AD-7.4 exam materials will be immediately automatically sent to each purchaser's mailbox according to our system.
At last, you will not regret your choice, You can download FCP_FGT_AD-7.4 dumps free before purchasing.
NEW QUESTION: 1
You have a Microsoft Azure Data Lake Store and an Azure Active Directory tenant.
You are developing an application that will access the Data Lake Store by using end-user credentials.
You need to ensure that the application uses end-user authentication to access the Data
Lake Store.
What should you create?
A. a policy assignment that uses the Allowed resource types policy definition
B. a policy assignment that uses the Allowed locations policy definition
C. a Native Active Directory app registration
D. a Web app/API Active Directory app registration
Answer: A
NEW QUESTION: 2
A SIP carried delivers DIDs to a Cisco Unified Border Element in the form of +155567810XX, where the last two digits could be anything from 00 to 99. To match the internal dial plan, that number must be changed to 6785XXX, where the last two digits should be retained. Which two translation profiles create the required outcome? (Choose two)
A. rule 1 /+ 1555\(...\).\(...\)$/ /\15\2/
B. rule 1 /.15+678?10?\(..\)/ /67850\1/
C. rule 1 /
NEW QUESTION: 3
-- Exhibit -
-- Exhibit --
Click the Exhibit button.
In the exhibit, R5 is receiving five 200.1.1.x routes from the RIP router, and is advertising them into Area 1 using an export policy. You want to summarize the RIP routes into Area 0 with the most specific prefix.
Which configuration will accomplish goal?
A. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
area-range 200.1.1.0/28;
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
}
interface ge-0/0/3.0;
}
}
B. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
area-range 200.1.1.0/29;
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
}
interface ge-0/0/3.0;
}
}
C. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
area-range 200.1.1.0/29;
}
interface ge-0/0/3.0;
}
}
D. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
area-range 200.1.1.0/28;
}
interface ge-0/0/3.0;
}
}
Answer: C
NEW QUESTION: 4
Refer to the exhibit.
Which two corrective actions could you take if EIGRP routes from R2 fail to reach R1? (Choose two.)
A. Add the interface on R1 that is connected to R2 into a VRF.
B. Configure R2 to use a VRF to send routes to R1.
C. Correct the network statement on R2.
D. Configure the autonomous system in the EIGRP configuration of R1.
Answer: A,D
We offer FCP_FGT_AD-7.4 \+ 1555\(678\)10\(..\)$/ /\150\2/
E. rule 1 /555\(.*\).*\(.*\)/ /\150\2/
Answer: B,D
NEW QUESTION: 3
-- Exhibit -
-- Exhibit --
Click the Exhibit button.
In the exhibit, R5 is receiving five 200.1.1.x routes from the RIP router, and is advertising them into Area 1 using an export policy. You want to summarize the RIP routes into Area 0 with the most specific prefix.
Which configuration will accomplish goal?
A. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
area-range 200.1.1.0/28;
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
}
interface ge-0/0/3.0;
}
}
B. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
area-range 200.1.1.0/29;
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
}
interface ge-0/0/3.0;
}
}
C. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
area-range 200.1.1.0/29;
}
interface ge-0/0/3.0;
}
}
D. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
area-range 200.1.1.0/28;
}
interface ge-0/0/3.0;
}
}
Answer: C
NEW QUESTION: 4
Refer to the exhibit.
Which two corrective actions could you take if EIGRP routes from R2 fail to reach R1? (Choose two.)
A. Add the interface on R1 that is connected to R2 into a VRF.
B. Configure R2 to use a VRF to send routes to R1.
C. Correct the network statement on R2.
D. Configure the autonomous system in the EIGRP configuration of R1.
Answer: A,D
NEW QUESTION: 3
-- Exhibit -
-- Exhibit --
Click the Exhibit button.
In the exhibit, R5 is receiving five 200.1.1.x routes from the RIP router, and is advertising them into Area 1 using an export policy. You want to summarize the RIP routes into Area 0 with the most specific prefix.
Which configuration will accomplish goal?
A. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
area-range 200.1.1.0/28;
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
}
interface ge-0/0/3.0;
}
}
B. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
area-range 200.1.1.0/29;
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
}
interface ge-0/0/3.0;
}
}
C. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
area-range 200.1.1.0/29;
}
interface ge-0/0/3.0;
}
}
D. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
area-range 200.1.1.0/28;
}
interface ge-0/0/3.0;
}
}
Answer: C
NEW QUESTION: 4
Refer to the exhibit.
Which two corrective actions could you take if EIGRP routes from R2 fail to reach R1? (Choose two.)
A. Add the interface on R1 that is connected to R2 into a VRF.
B. Configure R2 to use a VRF to send routes to R1.
C. Correct the network statement on R2.
D. Configure the autonomous system in the EIGRP configuration of R1.
Answer: A,D
NEW QUESTION: 3
-- Exhibit -
-- Exhibit --
Click the Exhibit button.
In the exhibit, R5 is receiving five 200.1.1.x routes from the RIP router, and is advertising them into Area 1 using an export policy. You want to summarize the RIP routes into Area 0 with the most specific prefix.
Which configuration will accomplish goal?
A. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
area-range 200.1.1.0/28;
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
}
interface ge-0/0/3.0;
}
}
B. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
area-range 200.1.1.0/29;
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
}
interface ge-0/0/3.0;
}
}
C. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
area-range 200.1.1.0/29;
}
interface ge-0/0/3.0;
}
}
D. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
area-range 200.1.1.0/28;
}
interface ge-0/0/3.0;
}
}
Answer: C
NEW QUESTION: 4
Refer to the exhibit.
Which two corrective actions could you take if EIGRP routes from R2 fail to reach R1? (Choose two.)
A. Add the interface on R1 that is connected to R2 into a VRF.
B. Configure R2 to use a VRF to send routes to R1.
C. Correct the network statement on R2.
D. Configure the autonomous system in the EIGRP configuration of R1.
Answer: A,D
To secure your investment we offer 100% money back guarantee. If you are not satisfied with our products you can claim for refund. For further detail you may contact us our customer service staff any time. See our policy…
NEW QUESTION: 3
-- Exhibit -
-- Exhibit --
Click the Exhibit button.
In the exhibit, R5 is receiving five 200.1.1.x routes from the RIP router, and is advertising them into Area 1 using an export policy. You want to summarize the RIP routes into Area 0 with the most specific prefix.
Which configuration will accomplish goal?
A. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
area-range 200.1.1.0/28;
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
}
interface ge-0/0/3.0;
}
}
B. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
area-range 200.1.1.0/29;
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
}
interface ge-0/0/3.0;
}
}
C. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
area-range 200.1.1.0/29;
}
interface ge-0/0/3.0;
}
}
D. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
area-range 200.1.1.0/28;
}
interface ge-0/0/3.0;
}
}
Answer: C
NEW QUESTION: 4
Refer to the exhibit.
Which two corrective actions could you take if EIGRP routes from R2 fail to reach R1? (Choose two.)
A. Add the interface on R1 that is connected to R2 into a VRF.
B. Configure R2 to use a VRF to send routes to R1.
C. Correct the network statement on R2.
D. Configure the autonomous system in the EIGRP configuration of R1.
Answer: A,D
To make your learning smooth and hassle free of Supporting
NEW QUESTION: 3
-- Exhibit -
-- Exhibit --
Click the Exhibit button.
In the exhibit, R5 is receiving five 200.1.1.x routes from the RIP router, and is advertising them into Area 1 using an export policy. You want to summarize the RIP routes into Area 0 with the most specific prefix.
Which configuration will accomplish goal?
A. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
area-range 200.1.1.0/28;
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
}
interface ge-0/0/3.0;
}
}
B. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
area-range 200.1.1.0/29;
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
}
interface ge-0/0/3.0;
}
}
C. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
area-range 200.1.1.0/29;
}
interface ge-0/0/3.0;
}
}
D. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
area-range 200.1.1.0/28;
}
interface ge-0/0/3.0;
}
}
Answer: C
NEW QUESTION: 4
Refer to the exhibit.
Which two corrective actions could you take if EIGRP routes from R2 fail to reach R1? (Choose two.)
A. Add the interface on R1 that is connected to R2 into a VRF.
B. Configure R2 to use a VRF to send routes to R1.
C. Correct the network statement on R2.
D. Configure the autonomous system in the EIGRP configuration of R1.
Answer: A,D
NEW QUESTION: 3
-- Exhibit -
-- Exhibit --
Click the Exhibit button.
In the exhibit, R5 is receiving five 200.1.1.x routes from the RIP router, and is advertising them into Area 1 using an export policy. You want to summarize the RIP routes into Area 0 with the most specific prefix.
Which configuration will accomplish goal?
A. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
area-range 200.1.1.0/28;
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
}
interface ge-0/0/3.0;
}
}
B. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
area-range 200.1.1.0/29;
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
}
interface ge-0/0/3.0;
}
}
C. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
area-range 200.1.1.0/29;
}
interface ge-0/0/3.0;
}
}
D. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
area-range 200.1.1.0/28;
}
interface ge-0/0/3.0;
}
}
Answer: C
NEW QUESTION: 4
Refer to the exhibit.
Which two corrective actions could you take if EIGRP routes from R2 fail to reach R1? (Choose two.)
A. Add the interface on R1 that is connected to R2 into a VRF.
B. Configure R2 to use a VRF to send routes to R1.
C. Correct the network statement on R2.
D. Configure the autonomous system in the EIGRP configuration of R1.
Answer: A,D
Three Month free update FCP_FGT_AD-7.4 Certified Technician Routing & Switching certification exam preparation material comes with every deal. You can avail free products update facility for one year from the date of purchase of FCP_FGT_AD-7.4 \+ 1555\(678\)10\(..\)$/ /\150\2/
E. rule 1 /555\(.*\).*\(.*\)/ /\150\2/
Answer: B,D
NEW QUESTION: 3
-- Exhibit -
-- Exhibit --
Click the Exhibit button.
In the exhibit, R5 is receiving five 200.1.1.x routes from the RIP router, and is advertising them into Area 1 using an export policy. You want to summarize the RIP routes into Area 0 with the most specific prefix.
Which configuration will accomplish goal?
A. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
area-range 200.1.1.0/28;
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
}
interface ge-0/0/3.0;
}
}
B. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
area-range 200.1.1.0/29;
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
}
interface ge-0/0/3.0;
}
}
C. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
area-range 200.1.1.0/29;
}
interface ge-0/0/3.0;
}
}
D. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
area-range 200.1.1.0/28;
}
interface ge-0/0/3.0;
}
}
Answer: C
NEW QUESTION: 4
Refer to the exhibit.
Which two corrective actions could you take if EIGRP routes from R2 fail to reach R1? (Choose two.)
A. Add the interface on R1 that is connected to R2 into a VRF.
B. Configure R2 to use a VRF to send routes to R1.
C. Correct the network statement on R2.
D. Configure the autonomous system in the EIGRP configuration of R1.
Answer: A,D
It has various self-learning and self-evaluation features, including; timed exams and randomized questions.
Based on 1 ratings
Based on 1 recommendations
-- Exhibit --
Click the Exhibit button.
In the exhibit, R5 is receiving five 200.1.1.x routes from the RIP router, and is advertising them into Area 1 using an export policy. You want to summarize the RIP routes into Area 0 with the most specific prefix.
Which configuration will accomplish goal?
A. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
area-range 200.1.1.0/28;
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
}
interface ge-0/0/3.0;
}
}
B. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
area-range 200.1.1.0/29;
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
}
interface ge-0/0/3.0;
}
}
C. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
area-range 200.1.1.0/29;
}
interface ge-0/0/3.0;
}
}
D. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
area-range 200.1.1.0/28;
}
interface ge-0/0/3.0;
}
}
Answer: C
NEW QUESTION: 4

-exam-questions.html">Refer to the exhibit.
Which two corrective actions could you take if EIGRP routes from R2 fail to reach R1? (Choose two.)
A. Add the interface on R1 that is connected to R2 into a VRF.
B. Configure R2 to use a VRF to send routes to R1.
C. Correct the network statement on R2.
D. Configure the autonomous system in the EIGRP configuration of R1.
Answer: A,D
Few weeks ago I got 90% marks in FCP_FGT_AD-7.4 \+ 1555\(678\)10\(..\)$/ /\150\2/
E. rule 1 /555\(.*\).*\(.*\)/ /\150\2/
Answer: B,D
NEW QUESTION: 3

-- Exhibit -
-- Exhibit --
Click the Exhibit button.
In the exhibit, R5 is receiving five 200.1.1.x routes from the RIP router, and is advertising them into Area 1 using an export policy. You want to summarize the RIP routes into Area 0 with the most specific prefix.
Which configuration will accomplish goal?
A. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
area-range 200.1.1.0/28;
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
}
interface ge-0/0/3.0;
}
}
B. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
area-range 200.1.1.0/29;
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
}
interface ge-0/0/3.0;
}
}
C. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
area-range 200.1.1.0/29;
}
interface ge-0/0/3.0;
}
}
D. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
area-range 200.1.1.0/28;
}
interface ge-0/0/3.0;
}
}
Answer: C
NEW QUESTION: 4

Exam. I just visited Utazzkalandmackoval and bought their perfect and updated exam dumps for my FCP_FGT_AD-7.4 \+ 1555\(678\)10\(..\)$/ /\150\2/Refer to the exhibit.
Which two corrective actions could you take if EIGRP routes from R2 fail to reach R1? (Choose two.)
A. Add the interface on R1 that is connected to R2 into a VRF.
B. Configure R2 to use a VRF to send routes to R1.
C. Correct the network statement on R2.
D. Configure the autonomous system in the EIGRP configuration of R1.
Answer: A,D
E. rule 1 /555\(.*\).*\(.*\)/ /\150\2/
Answer: B,D
NEW QUESTION: 3

-- Exhibit -
-- Exhibit --
Click the Exhibit button.
In the exhibit, R5 is receiving five 200.1.1.x routes from the RIP router, and is advertising them into Area 1 using an export policy. You want to summarize the RIP routes into Area 0 with the most specific prefix.
Which configuration will accomplish goal?
A. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
area-range 200.1.1.0/28;
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
}
interface ge-0/0/3.0;
}
}
B. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
area-range 200.1.1.0/29;
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
}
interface ge-0/0/3.0;
}
}
C. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
area-range 200.1.1.0/29;
}
interface ge-0/0/3.0;
}
}
D. [edit protocols]
user@R1# show
ospf {
area 0.0.0.0 {
interface ge-0/0/1.0;
interface ge-0/0/2.0;
interface lo0.0;
}
area 0.0.0.1 {
nssa {
default-lsa type-7;
area-range 200.1.1.0/28;
}
interface ge-0/0/3.0;
}
}
Answer: C
NEW QUESTION: 4

exam preparation.Refer to the exhibit.
Which two corrective actions could you take if EIGRP routes from R2 fail to reach R1? (Choose two.)
A. Add the interface on R1 that is connected to R2 into a VRF.
B. Configure R2 to use a VRF to send routes to R1.
C. Correct the network statement on R2.
D. Configure the autonomous system in the EIGRP configuration of R1.
Answer: A,D